Difference between revisions of "Maintenace"
(→Fire Protection) |
(→HVAC Details) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 50: | Line 50: | ||
* Thermostat Controls both Heating & Cooling to the office space | * Thermostat Controls both Heating & Cooling to the office space | ||
* The unit is located above the bathroom. | * The unit is located above the bathroom. | ||
| − | |||
| − | |||
'''Shop''' | '''Shop''' | ||
* Unit 1 furnace provides heat only only to the wood shop. | * Unit 1 furnace provides heat only only to the wood shop. | ||
| − | |||
==Electrical== | ==Electrical== | ||
| − | + | Circuit Breakers are located in the utility closet, the wall of the woodshop, and the wall of the metal shop. If a circuit is tripped, the relevant breaker will show an orange indicator. '''ALWAYS POWER OFF ALL EQUIPMENT PLUGGED IN BEFORE RESETING A BREAKER.''' | |
| − | + | *Utility Closet 200A | |
| − | + | ** Circuits in the office, including the laser, terminate here. | |
| − | + | *Wood Shop 100A | |
| − | ** | + | ** Most outlets in the wood shop terminate here. |
| + | *Metal Shop 80A | ||
| + | ** This subpanel contains all circuits in the metal shop. | ||
==Fire Protection== | ==Fire Protection== | ||
Fire Code compliance | Fire Code compliance | ||
| − | '''Fire Extinguishers:''' There are | + | '''Fire Extinguishers:''' There are six wall mounted fire extinguishers for the space: |
* Unit 1: | * Unit 1: | ||
** Front lobby by kitchenette | ** Front lobby by kitchenette | ||
Latest revision as of 04:57, 16 June 2023
The space requires minimal maintenance but the items detailed below are required. Use the Blog:Maintenance to log maintenance activities.
Report all findings, issues, questions, and concerns to the makerspace Board of Directors
| Item | Frequency | Notes | |
| Trash | Weekly | Dumpster is located outside the back of Unit 1. Please do not leave any food trash inside the office. Take it directly to the dumpster | |
| Front Door | Weekly | Confirm door/lock are in good condition. Sweep Entrance | |
| HVAC | Twice per year | There are 3 HVAC zones in the space see details below | |
| Bathroom | Monthly | Check for Leaks Clean sink & toilet Replenish toilet paper & towels | |
| Back Doors | Weekly | Confirm no items blocking the fire exit **Confirm no items blocking the fire exit Make sure the back door fire exit is not blocked | |
| Roll Up Doors | Weekly | Confirm roll up chain is not binding | |
| Back Shops | Weekly | Vacuum & Sweep sawdust and debris | Confirm dust collectors are not full |
HVAC Details
There are 2 HVAC zones in the space:
Unit 1
- Thermostat Controls both Heating & Cooling to the office space
- The unit is located above the bathroom.
Shop
- Unit 1 furnace provides heat only only to the wood shop.
Electrical
Circuit Breakers are located in the utility closet, the wall of the woodshop, and the wall of the metal shop. If a circuit is tripped, the relevant breaker will show an orange indicator. ALWAYS POWER OFF ALL EQUIPMENT PLUGGED IN BEFORE RESETING A BREAKER.
- Utility Closet 200A
- Circuits in the office, including the laser, terminate here.
- Wood Shop 100A
- Most outlets in the wood shop terminate here.
- Metal Shop 80A
- This subpanel contains all circuits in the metal shop.
Fire Protection
Fire Code compliance
Fire Extinguishers: There are six wall mounted fire extinguishers for the space:
- Unit 1:
- Front lobby by kitchenette
- Woodshop by office door
- Woodshop on pillar by SawStop
- Woodshop by rear walk-in door
- Electronics Room near Laser (C02)
- 3d Printing Room by door
